Author Guidelines

Title 12 font-size Cambria left aligned and bold

Download Template

Full Name*1, Full Name 2, Full Name 3 

1. INTRODUCTION (CAMBRIA, CAPITAL, BOLD 10 FONT SIZE)
   
   Content should be written in 2 columns with Cambria 10 font size. The first line of each paragraph should be written by 0.7 cm indentation.
   The article should begin with an introduction section, which includes the ideas and the basic objectives and approaches of the article, combining scientific knowledge, evidence-based information, and logical discussions in different disciplines. This section should be written considering all readers. Technical terms, symbols, and abbreviations should be defined when first used in the article.
   The main sections of the manuscript are “introduction”, “method” “results” “discussion” and “conclusion” and they should be written in 10 font sizes, justify bold and capital letters.
   This template explains how to design the manuscript. If the author (s) uses this template file, no settings change will be required since settings such as font and size, line spacing, spaces before paragraphs, indents, etc. are made in styles. If you want to avoid problems when copy and paste texts or with the text format, you can use the “Applying styles to the article” section which is at the end of the template.
   
   2. METHOD (CAMBRIA, CAPITAL, BOLD 10 FONT SIZE)
   
   Content should be written in 2 columns with Cambria 10 font size.
   “Introduction” part should be followed by “Method”, “Results”, “Discussion” and “Conclusion” parts.
   The article should be saved in MS Office Word as either .doc or Docx. The text should be written as A4 size with 2 cm spacing at the top, bottom, left, and right side. The text should be written with single line spacing. Page numbers should not be added.
   Articles prepared in accordance with the principles of writing and approved by the review board are published.
   
   2.1. The Second Level Headings (Cambria, First Character Capital, Bold 10 Font Size)
   
   Content should be written in 2 columns with Cambria 10 font size.
   The second-level headings should be written with left-aligned, 10 font size, first character capital, bold. Each paragraph should separate with one line from the former paragraph. You can delete this section and write the article text without disturbing the formatting.
   No spaces should be left between paragraphs in the text.
   
   2.2. The second Level Headings (Cambria, First Character Capital, Bold, 10 Font Size)
   
   The second-level headings should be written with left-aligned, 10 font size, first character capital, bold. Each paragraph should separate with one line from the former paragraph. You can delete this section and write the article text without disturbing the formatting.
   No spaces should be left between paragraphs in the text.

Figures should be left and right-aligned and numbered. Figure caption should be written 10 font size, Cambria, the first letter of first-word capital. It should not be written in bold or italic. A dot should be placed after the figure number.
Text in the figure should be 9 font size. A line should not exist between figure and figure caption. A line should exist between text and figure. Figure caption should be located under the figure. Figures should be cited in the text as “Fig. 1”.

2.2.1. Third-level heading (Cambria, only first letter capital, bold 10 font size)

The only first letter of the first word is capital, justified, 10 font size. It should be separated from the former paragraph with a single line.

3. RESULTS (CAMBRIA, CAPITAL, BOLD,10 FONT SIZE)

References, tables, figures to be used must be prepared in accordance with APA 6. Articles that do not comply with the rules of writing and APA are eliminated in the first stage by the editor. You should review your references and check their compliance with APA 6. Tables must be cited in the text together with the table number as “Table 1”.

Tables should be numbered and the title of the table should be written in 10 pt. Table title should not be bold or italic. The table number should be followed by a dot and the table name should be written. No dot should be placed after the table name is written. Please do not use vertical lines in Tables.
In-table values / inscriptions should be 9 pt. No spaces should be left between the table title and the table. Tables should be specified in the text with the number of tables. Tables should be used in the text or on the following page. Related notes and references should be indicated at the bottom of the table after “Note:” or “Source:”. The space between the text and the table before and after the table must be 1 row.

4. CONCLUSION (CAMBRIA, CAPITAL, BOLD 10 FONT SIZE)

Citation in text should be as;
Single author
...(Ulvi 2020)
Two authors
...(Ulvi and Yakar 2018)
Three or more authors
...(Ulvi et al. 2014)
Two references
...(Yigit et al. 2018; Yakar 2019)

More than one references in the same parenthesis should be made with the alphabetical order.
Bibliography should be prepared in accordance with the APA 6 Publication Manual publication guidelines. For more information; See http://www.apa.org. References should be written in alphabetical order with 10 pt including title. The paragraph indent is 0.7 cm hanging from the right.
The second and subsequent lines of each bibliography should be indented 0.7 cm inward as shown in this text. There will be a gap between the sources.
Thesis should be written as Master’s Thesis or Doctoral Thesis in the reference list.

ACKNOWLEDMENT

Acknowledgements of support for the project/paper/author are welcome.

REFERENCES

References should be written like this. All of the references should be written in alphabetical order.

Articles

Alptekin A & Taga H (2019). Prediction of compression and swelling index parameters of Quaternary sediments from index tests at Mersin District. Open Geosciences, 11(1), 482-491.

Iban M C (2020). Geospatial Data Science Response to COVID-19 Crisis and Pandemic Isolation Tracking. Turkish Journal of Geosciences, 1(1), 1-7.

Yakar M, Yılmaz H M & Mutluoglu O (2014). Performance of Photogrammetric and Terrestrial Laser Scanning Methods in Volume Computing of Excavation and Filling Areas. Arabian Journal for Science and Engineering, 39, 387-394.

Books

Maune D F (2001) Digital elevation model technologies and applications: The DEM User manual. The American Society for Photogrammetry and Remote Sensing. ISBN:1-57083-064-9

Conference

Ulvi A, Varol F & Yiğit A Y (2019). 3D modeling of cultural heritage: the example of Muyi Mubarek Mosque in Uzbekistan (Hz. Osman’s Mushafi). International Congress on Cultural Heritage and Tourism (ICCHT), 115-123, Bishkek, Kyrgyzstan.

Thesis

Alptekin A (2016) Determination of index and consolidation properties of cohesive soils located at the urban settlement of the Mersin province. Master’s Thesis, Mersin University, Institute of Science, Mersin, 79p (in Turkish).